In the “Settings” tab select the “Auxiliary equipment” section from the list.

In the “Accelerometer parameters” section:

“Accelerometer” – enable/disable the use of accelerometer for measuring the vehicle acceleration.

“Accelerometer status” – accelerometer condition. Possible options: not used, calibration, calibrated, calibration error.

“Accelerometer calibration” – select the accelerometer calibration mode. Possible options: automatic calibration, manual calibration.

Automatic calibration is recommended for vehicles that are operated mainly at speeds above 50 km/h. Automatic calibration takes from 2 minutes to 24 hours depending on the frequency of accelerations and braking on straight sections of the road.

When selecting manual calibration, in the “Position of the terminal” field, select one of 24 positions as shown in figure

Arrow ► indicates the location of the terminal connector.

The “Omnicomm” inscription in the figure corresponds to the top cover of the terminal.

In the “Settings” tab select the “Driving Control” section from the list.

“Control of dangerous driving” – enable/disable registration of dangerous driving when exceeding the set values of monitored parameters.

Select monitored parameters:

“Sending an event” – enable/disable event sending to Omnicomm Online.

• “Speed” – vehicle speed control

Threshold – enter the maximum permissible speed, upon exceeding which dangerous driving will be registered. Possible values: from 0 to 150 km/h. Default value: 80 km/h.

Deviation – enter the speed value that can be exceeded maximum permissible speed without triggering dangerous driving. Possible values: from 0 to 50 km/h. Default value: 5 km/h.

Duration – enter the period of time allowed to exceed maximum permissible speed without triggering dangerous driving. Possible values: from 0 to 300 s. Default value: 15 s.

• “Engine speed (RPM)” – engine RPM monitoring

Threshold – enter the maximum permissible engine RPM, upon exceeding which dangerous driving will be registered. Possible values: from 0 to 10,000 rpm. Default value: 4,000 rpm.

Deviation – enter the RPM value that can be exceeded by maximum permissible RPM without registration of violation. Possible values: from 0 to 1000 rpm. Default value: 200 rpm.

Duration – enter the period of time allowed to exceed maximum permissible engine RPM without registration of dangerous driving. Possible values: from 0 to 300 s. Default value: 15 s.

• “Acceleration” – acceleration control during vehicle speeding up

Threshold – enter the value of acceleration while speeding up, which exceeding will trigger registration of dangerous driving

• “Lateral acceleration” – acceleration control during vehicle turning

Threshold – enter the value of acceleration while turning, which exceeding will trigger registration of dangerous driving

• “Braking” – acceleration control during vehicle braking

Threshold – enter the value of acceleration while braking, which exceeding will trigger registration of dangerous driving

• “Vertical acceleration (jolt / shock)” – acceleration control during vehicle jolting

Threshold – enter the value of acceleration while jolting or shocking, which exceeding will trigger registration of dangerous driving

• “Speed and threshold exceeding of potential UI1”

Threshold – enter the value of speed, which exceeding will trigger registration of violation, if universal input No.1 is closed/open.

• “Speed and threshold exceeding of potential UI2”

Threshold – enter the value of speed, which exceeding will trigger registration of violation, if universal input No.2 is closed/open.

• “Send an SMS for selected events” – enable SMS sending upon registration of dangerous driving
• “Send a photo for selected events” – enable digital camera photo sending upon registration of dangerous driving

“Sound notification” – enable/disable sound notification if thresholds of monitored parameters are exceeded. To run sound notification connect a sound emitter to controlled output No.1.

“Identify an accident” – enable/disable accident registration upon exceeding the set values of monitored parameters.

• “Acceleration threshold” – value of acceleration while speeding up, which exceeding will trigger registration of accident
• “Lateral acceleration threshold” – value of acceleration while turning, which exceeding will trigger registration of accident
• “Threshold of braking” – value of acceleration while braking, which exceeding will trigger registration of accident
• “Send SMS upon triggering” – enable SMS sending upon registration of accident
• “Send photo upon triggering” – enable digital camera photo sending upon registration of accident

“Load on axes” – enable/disable control of vehicle axle load and total vehicle load.

“Data source” displays the axle load data source. Possible options: ALM Weight Indicator and CAN.

To select the ALM Weight Indicator as a data source choose Indicator in the RS-485 or RS-232 interface configuration.

To select the CAN bus as a data source enable SPN 582 and SPN 928 in the CAN settings tab.

If the ALM Weight Indicator and the CAN Bus are both set as data source, the ALM Weight Indicator will be used.

“Axle count” – set the number of vehicle axles. Possible values: from 1 to 8. Maximum value – 8 for CAN, 6 for ALM.

“Threshold of axle load, tons” – enter the value of load on each axle, upon exceeding which an event will be registered.

• “Sound notification” – enable/disable sound notification if thresholds of monitored parameters are exceeded.
• “Events” – enable/disable event sending to Omnicomm Online
• “Photo” – enable digital camera photo sending upon load exceeding
• “SMS” – enable SMS sending upon load exceeding

“Overall load threshold, tons” – enter the value of total vehicle load, upon exceeding which an event will be registered.

• “Sound notification” – enable/disable sound notification if thresholds of monitored parameters are exceeded.
• “Events” – enable/disable event sending to Omnicomm Online
• “Photo” – enable digital camera photo sending upon total load exceeding
• “SMS” – enable SMS sending upon total load exceeding