In the “Settings” tab select the “Connection” section from the list.

In the “GPRS Setup” section:

“Access Point Name (APN)” – enter the GPRS access point name

For GPRS access point names of other operators, refer to the mobile network operator, whose SIM card is inserted in the terminal.

“Phone number” – number of the SIM card inserted in the terminal.

“APN Login” and “APN Password” – if necessary, enter login and password for APN access point. Login and password are provided with the SIM card of a number of mobile network operators.

Terminals support data transmission to two Communication Servers (CS) through Omnicomm and EGTS protocols.

In the “Settings” tab select the “Connection” section from the list.

In the “EGTS Protocol Settings” section:

When setting up EGTS data transmission, you must use the TID terminal identification.

If the settings are not configured, when transmitting data through EGTS protocol ID Omnicomm will be used for terminal identification.

In the “Settings of connection to the communication server” sections:

“IP address or domain name of CS 1” – enter IP address or domain name of the communication server: cs.dc1.omnicomm.ru.

“Port” – enter port to be used by terminal to connect to the communication server: 9977

“Protocol” – select data transmission protocol to the CS. Possible options: Omnicomm or EGTS.

In the “Settings” tab select the “Connection” section from the list.

In the “Data collection parameters” section:

“Data collection timer” – set the value of the period of Terminal requesting modules and external devices connected to it. Default value - 15 seconds. Value range - from 1 to 240 seconds (except for Smart). Value range for Smart - from 15 to 240 seconds.

“Operation with ignition off and power on” select:

• “Collect all data” – data collection and transmission same as with ignition turned on
• “Collect all except GPS” – collection and transmission of data selected during configuration of the terminal, except for the GPS module data
• “Сollect data at jolting” – monitoring the status of the panic button and accelerometer. If the accelerometer reading changes by more than 0.2 g or the panic button is pressed, the terminal switches to the “Collect all data” and performs data transmission to the Communication Server in 5 minutes

When selecting “Collect data during pounding” set the following configuration:

• “Collect all data” – when this parameter is enabled, the terminal upon expiration of the time specified in the “Period of data sending to server” switches to the “Collect all data” mode and performs data collection and transmission to the communication server. After the data transmission the terminal switches to the “Collect data during pounding” mode.
• “Interval of data sending to the server” – the time interval between the terminal connections to CS. Possible values: from 1 to 6 hours, at intervals of 1 hour.

Depending on the set mode, the data are collected from the particular modules and external devices.

“Adaptive data collection at cornering” – enable/disable adaptive data collection on turns, which allows increasing the accuracy of displaying turns on the map by additional data collection from the GPS module more frequently than set in the “Data collection timer” parameter. This mode is active only when the terminal registers that the ignition is on.

“Collecting data on the travelled distance” – allows increasing the accuracy of displaying the vehicle location on the map by additional data collection from the GPS module over the distance travelled between the events with registered coordinates.

“Distance travelled” – enter the mileage travelled from the moment of the last registered event with coordinates, upon achieving which the data will be collected. Possible values: from 10 to 1000 meters. Default value – 100 meters.

“Coordinate drift filtering” – enable to eliminate drift of coordinates during the “Track” report generation.

When enabling the “Coordinate drift filtering” the following settings are available:

• “Delay after ignition on, sec”. Default value – 35 sec. Possible values: from 0 to 900.
• “Maximum movement speed, km/h”. Default value – 180 km/h. Possible values: from 5 to 360.

The default values allow elimination of drifts for most cases and do not require correction.

In the “Settings” tab select the “Connection” section from the list.

In the “Parameters of output for connection” section:

“Interval of sending data to the CS” – enter the number of minutes, upon expiration of which the Terminal must establish connection with the communication server, while being in the mobile operator's home network. Recommended value – 10 minutes.

In the “GSM and SMS communication parameters” section:

“SMS” – enable/disable the commands reception via SMS and sending the information messages by the Terminal. When the “SMS” parameter is enabled:

“SMS destination number” – enter the phone number, to which the SMS will be sent with information about the status of the Terminal and the vehicle.

“Language of SMS template” – select the language of the SMS template. Possible options: Russian, English, Portuguese, Spanish.

“Vehicle Name” – enter the name of the vehicle. The “Vehicle Name” field is mandatory.

In the “Output parameters to communicate in roaming” section:

Select the criterion for the terminal connection to the CS: “By time period” or “By packet size”.

“Interval of sending data to the CS” – enter the number of minutes, upon expiration of which the terminal must establish connection with the communication server, while being in roaming. Recommended value – 180 minutes.

“Data packet size to send to CS” – enter the data packet size, upon achieving which the terminal must establish connection with the communication server, while being in roaming. Recommended value – 100 Kb.

In the “Roaming settings” section:

To use the SIM card in roaming “according to the list”, in Omnicomm Configurator, enter the MCC and MNC table of authorized cellular networks.

In the “Settings” tab select the “Inputs” section from the list.

In the “Ignition key status” section: “Data source” – select the data to register ignition on/off.

Possible options:

“Ignition key” – the ignition on/off is registered on the position of the key upon direct connection to the ignition key.

“Onboard voltage” – the ignition on is registered upon reaching the vehicle network power supply threshold voltage. Specify the value “Threshold voltage, V” – the value of the vehicle network power supply voltage, upon reaching which the ignition on will be registered. Ignition off is registered, when the voltage drops to 0.5 V below the threshold.

In the “Settings” tab select the “Inputs” section from the list.

In the “Vehicle speed” section:

“Data source” – select the data to process the speed values. Possible options: “GPS” or “CAN bus”.

In the “Settings” tab select the “Inputs” section from the list.

In the “Engine RPM” section:

“Data source” – select the signal type. Possible values:

• “Disabled”
• “Ignition key“
• “CAN bus”
• “RPM input”

Connect the tachometer to the Smart and Light Terminals according to the diagram:

The place of connection to the tachometer shall be the point in the vehicle electric network, in which the pulse signal frequency is proportional to the engine RPM.

In the “Settings” tab select the “Auxiliary equipment” section from the list.

In the “Accelerometer parameters” section:

“Accelerometer” – enable/disable the use of accelerometer for measuring the vehicle acceleration.

“Accelerometer status” – accelerometer condition. Possible options: not used, calibration, calibrated, calibration error.

“Accelerometer calibration” – select the accelerometer calibration mode. Possible options: automatic calibration, manual calibration.

Automatic calibration is recommended for vehicles that are operated mainly at speeds above 50 km/h. Automatic calibration takes from 2 minutes to 24 hours depending on the frequency of accelerations and braking on straight sections of the road.

When selecting manual calibration, in the “Position of the terminal” field, select one of 24 positions as shown in figure

Arrow ► indicates the location of the terminal connector.

The “Omnicomm” inscription in the figure corresponds to the top cover of the terminal.

In the “Settings” tab select the “Driving Control” section from the list.

“Control of dangerous driving” – enable/disable registration of dangerous driving when exceeding the set values of monitored parameters.

Select monitored parameters:

“Sending an event” – enable/disable event sending to Omnicomm Online.

• “Speed” – vehicle speed control

Threshold – enter the maximum permissible speed, upon exceeding which dangerous driving will be registered. Possible values: from 0 to 150 km/h. Default value: 80 km/h.

Deviation – enter the speed value that can be exceeded maximum permissible speed without triggering dangerous driving. Possible values: from 0 to 50 km/h. Default value: 5 km/h.

Duration – enter the period of time allowed to exceed maximum permissible speed without triggering dangerous driving. Possible values: from 0 to 300 s. Default value: 15 s.

• “Engine speed (RPM)” – engine RPM monitoring

Threshold – enter the maximum permissible engine RPM, upon exceeding which dangerous driving will be registered. Possible values: from 0 to 10,000 rpm. Default value: 4,000 rpm.

Deviation – enter the RPM value that can be exceeded by maximum permissible RPM without registration of violation. Possible values: from 0 to 1000 rpm. Default value: 200 rpm.

Duration – enter the period of time allowed to exceed maximum permissible engine RPM without registration of dangerous driving. Possible values: from 0 to 300 s. Default value: 15 s.

• “Acceleration” – acceleration control during vehicle speeding up

Threshold – enter the value of acceleration while speeding up, which exceeding will trigger registration of dangerous driving

• “Lateral acceleration” – acceleration control during vehicle turning

Threshold – enter the value of acceleration while turning, which exceeding will trigger registration of dangerous driving

• “Braking” – acceleration control during vehicle braking

Threshold – enter the value of acceleration while braking, which exceeding will trigger registration of dangerous driving

• “Vertical acceleration (jolt / shock)” – acceleration control during vehicle jolting

Threshold – enter the value of acceleration while jolting or shocking, which exceeding will trigger registration of dangerous driving

• “Speed and threshold exceeding of potential UI1”

Threshold – enter the value of speed, which exceeding will trigger registration of violation, if universal input No.1 is closed/open.

• “Speed and threshold exceeding of potential UI2”

Threshold – enter the value of speed, which exceeding will trigger registration of violation, if universal input No.2 is closed/open.

• “Send an SMS for selected events” – enable SMS sending upon registration of dangerous driving
• “Send a photo for selected events” – enable digital camera photo sending upon registration of dangerous driving

“Sound notification” – enable/disable sound notification if thresholds of monitored parameters are exceeded. To run sound notification connect a sound emitter to controlled output No.1.

“Identify an accident” – enable/disable accident registration upon exceeding the set values of monitored parameters.

• “Acceleration threshold” – value of acceleration while speeding up, which exceeding will trigger registration of accident
• “Lateral acceleration threshold” – value of acceleration while turning, which exceeding will trigger registration of accident
• “Threshold of braking” – value of acceleration while braking, which exceeding will trigger registration of accident
• “Send SMS upon triggering” – enable SMS sending upon registration of accident
• “Send photo upon triggering” – enable digital camera photo sending upon registration of accident

“Load on axes” – enable/disable control of vehicle axle load and total vehicle load.

“Data source” displays the axle load data source. Possible options: ALM Weight Indicator and CAN.

To select the ALM Weight Indicator as a data source choose Indicator in the RS-485 or RS-232 interface configuration.

To select the CAN bus as a data source enable SPN 582 and SPN 928 in the CAN settings tab.

If the ALM Weight Indicator and the CAN Bus are both set as data source, the ALM Weight Indicator will be used.

“Axle count” – set the number of vehicle axles. Possible values: from 1 to 8. Maximum value – 8 for CAN, 6 for ALM.

“Threshold of axle load, tons” – enter the value of load on each axle, upon exceeding which an event will be registered.

• “Sound notification” – enable/disable sound notification if thresholds of monitored parameters are exceeded.
• “Events” – enable/disable event sending to Omnicomm Online
• “Photo” – enable digital camera photo sending upon load exceeding
• “SMS” – enable SMS sending upon load exceeding

“Overall load threshold, tons” – enter the value of total vehicle load, upon exceeding which an event will be registered.

• “Sound notification” – enable/disable sound notification if thresholds of monitored parameters are exceeded.
• “Events” – enable/disable event sending to Omnicomm Online
• “Photo” – enable digital camera photo sending upon total load exceeding
• “SMS” – enable SMS sending upon total load exceeding

In the “Settings” tab select the “Auxiliary equipment” section from the list.

In the “Case tampering detection” section:

“Send an SMS upon an attempt open the case” – enable/disable SMS sending upon triggering the body tampering sensor.

In the “Settings” tab select the “Auxiliary equipment” section from the list.

In the “Parameters of internal accumulator” section:

“Use built-in battery” – enable/disable use of internal battery when the main power supply is turned off and the terminal is operating in the “Collect data at jolting” mode.

For Omnicomm Light terminals in the “Settings” tab select the “Auxiliary equipment” section from the list.

In the “GPS / GLONASS Signals Jamming Detector” section:

“Send SMS upon GPS/GLONASS signals jamming attempts detection” – check the box to send SMS upon registering the jamming of GPS / GLONASS.

GPS/GLONASS jamming detector can be activated when SMS configuration is enabled (see GSM and SMS parameters).

For Omnicomm Light terminals in the “Settings” tab select the “Auxiliary equipment” section from the list.

In the “GSM Signal Jamming Detector” section:

GSM jamming detector can be activated when SMS configuration is enabled (see GSM and SMS parameters).

“Sending SMS on GSM signal jamming detection” – check the box to send SMS upon registering the GSM network signal jamming.