Installation
SIM Card Inserting
Before SIM card inserting disable PIN request at activation. For this end insert the card in any cell phone and disable PIN request, according to the cell phone operating instruction.
- Using a sharp-pointed object press the button on the terminal front panel. The SIM card holder will eject
- Remove the SIM card holder from the connector slots and insert the SIM card into it with contact pieces up
- Insert the SIM card holder in the connector slots:
SIM chip installation is available under custom order.
Second SIM Card and SD Card Inserting for Optim
- Unscrew the two screws fixing the terminal body
- Remove the upper body part
- Insert a miniSD card in the slot intended for SD card
- Insert the second SIM card in the slot as shown in figure:
Connector Pin Assignment
Omnicomm Profi terminals:
Omnicomm Profi Wi-Fi terminals:
Connector Х1:
| No. of pin | Signal name | Designation | Wire colour in cable |
|---|---|---|---|
| 1 | Ground (negative) for power supply | Ground (signal) | White |
| 2 | Ground (negative) for power supply | Ground (power) | White |
| 3 | Panic button | Panic button | White-red |
| 4 | Universal input 2 | Input 2 | Black-white |
| 5 | Universal input 4 | Input 4 | Black-yellow |
| 6 | RPM input | Tachometer | Blue |
| 7 | Controlled output 2 | Output 2 | Yellow-dark blue |
| 8 | Line RX RS-232 | RS-232 RX | Pink |
| 9 | Line B RS-485 №2 | B RS-485 №2 | Black-blue |
| 10 | Line B RS-485 №1 | B RS-485 №1 | Blue-white |
| 11 | CAN L | CAN L | Purple-white |
| 12 | Vehicle power supply voltage | Power (positive) | Red |
| 13 | Ignition key | IGN | Yellow |
| 14 | GSM Activation Button | GSM | Green-black |
| 15 | Universal input 1 | Input 1 | Black |
| 16 | Universal input 3 | Input 3 | Black-red |
| 17 | iButton+ | iButton+ | Pink-red |
| 18 | Controlled output 1 | Output 1 | Yellow-red |
| 19 | Line TX RS-232 | RS-232 TX | Grey |
| 20 | Line A RS-485 №2 | A RS-485 №2 | White-green |
| 21 | Line A RS-485 №1 | A RS-485 №1 | Orange-white |
| 22 | CAN Н | CAN Н | Purple-orange |
Connector Х2:
| No. of pin | Signal name | Designation | Wire colour in cable |
|---|---|---|---|
| 1 | Microphone- | Microphone- | Green-yellow |
| 2 | Speaker- | Speaker- | Grey-yellow |
| 3 | Ground | GND | White |
| 4 | Universal input 5 | Input 5 | Green |
| 5 | Ground | GND | White |
| 6 | Microphone+ | Microphone+ | Green-red |
| 7 | Speaker+ | Speaker+ | Grey-red |
| 8 | iButton- | iButton- | Pink-blue |
| 9 | Universal input 6 | Input 6 | Purple |
| 10 | Plus LLS sensor power supply | PWR LLS | Brown |
Omnicomm Optim terminal
Connector Х1:
| No. of pin | Signal name | Designation | Wire colour in cable |
|---|---|---|---|
| 1 | Ground (negative) for power supply | Ground (signal) | White |
| 2 | Ground (negative) for power supply | Ground (power) | White |
| 3 | Panic button | Panic button | White-red |
| 4 | Universal input 2 | Input 2 | Black-white |
| 5 | Universal input 4 | Input 4 | Black-yellow |
| 6 | RPM input | Tachometer | Blue |
| 7 | Controlled output 2 | Output 2 | Yellow-dark blue |
| 8 | Line RX RS-232 | RS-232 RX | Pink |
| 9 | Line B RS-485 №2 | B RS-485 №2 | Black-blue |
| 10 | Line B RS-485 №1 | B RS-485 №1 | Blue-white |
| 11 | CAN L | CAN L | Purple-white |
| 12 | Vehicle power supply voltage | Power | Red |
| 13 | Ignition key | IGN | Yellow |
| 14 | GSM Activation Button GSM | GSM | Green-black |
| 15 | Universal input 1 | Input 1 | Black |
| 16 | Universal input 3 | Input 3 | Black-red |
| 17 | iButton+ | iButton+ | Pink-red |
| 18 | Controlled output 1 | Output 1 | Yellow-red |
| 19 | Line TX RS-232 | RS-232 TX | Grey |
| 20 | Line A RS-485 №2 | A RS-485 №2 | White-green |
| 21 | Line A RS-485 №1 | A RS-485 №1 | Orange-white |
| 22 | CAN Н | CAN Н | Purple-orange |
Omnicomm Smart terminal
Connector Х1:
| No. of pin | Signal name | Designation | Wire colour in cable |
|---|---|---|---|
| 1 | Ground (minus) for power supply | Ground (signal) | White |
| 2 | RPM input | Tachometer | Dark blue |
| 3 | Not used | NC | |
| 4 | Not used | NC | |
| 5 | Line B RS-485 LLS | B RS-485 LLS | Blue-white |
| 6 | CAN L | CAN L | Purple-white |
| 7 | Vehicle power supply voltage | Power | Red |
| 8 | Ignition key | IGN | Yellow |
| 9 | Universal input 1 | Input 1 | Black |
| 10 | Not used | NC | |
| 11 | Line A RS-485 LLS | A RS-485 LLS | Orange-white |
| 12 | CAN Н | CAN Н | Purple-orange |
Protective Insert Placing for Optim
The protective insert is placed after SIM cards inserting, setting the terminal and before the connection of mounting cable connector and antennas.
1. Remove protective film from the insert
2. Carefully install the protective insert in the terminal body
Reinstallation of the protective insert is not possible
3. Treat the mounting cable connector wire exit points with silicone sealant or hot-melt glue
Power Supply and Ignition Key
Connect Omnicomm Profi, Profi Wi-Fi terminals as per diagrams without battery disconnect switch:
after ground disconnect switch:
before ground disconnect switch:
Connect Omnicomm Optim terminals as per diagrams without
ground disconnect switch:
after ground disconnect switch:
Connect Omnicomm Smart terminals as per diagrams without
ground disconnect switch:
after ground disconnect switch:
before ground disconnect switch:
Terminal
Omnicomm terminal shall be installed in the vehicle cabin or in specially equipped electrics boxes on the vehicle protected from atmospheric precipitation.
Drill 4 mounting holes Ø4 mm.
For Omnicomm Profi, Profi Wi-Fi terminals:
For Omnicomm Optim and Smart terminals:
Install the terminal and fix with self-tapping screws.
Antennas
Choose the installation site of antennas based on the antenna cable length.
It is recommended to install the GLONASS/GPS antenna on the roof of the vehicle. The GLONASS/GPS antenna must be installed on a metallic surface. It may be installed on a non-metallic surface if it is secured to the surface using glue.
The GLONASS/GPS antenna may be installed inside the vehicle, in a place providing good access to radio signal from the sky. Inside a vehicle, the antenna must be installed only on a horizontal surface and it is necessary to carry out a check of the reception quality of the GLONASS/GPS satellites.
Recommended installation site of GSM antenna: vehicle windshield or inner side of the vehicle plastic front panel.
Recommended installation site of Wi-Fi antenna of Profi Wi-Fi terminal: vehicle windshield or inner side of the vehicle plastic front panel.
Distance from antennas to any metal surface (except for the surface of installation) should be not less than 50 mm.
- Degrease the installation site surface
- Remove protective film from the double adhesive tape on the surface of antenna
- Attach the antenna with the adhesive side to the installation site
- Fix the antenna while the adhesive is setting
