SMS Commands
SMS commands for terminal management
| Command | Designation | |
|---|---|---|
| Command text in SMS | Reply to a command in SMS | |
| *SOUND 1# | SOUND ON | Request for turning on the siren |
| *SOUND 0# | SOUND OFF | Request for turning off the siren |
| *SETDOUT param# Param=0 Param=1 Param=0,1 | SETDOUT Possible parameter values: param = OK if the command is forwarded to execution param = ER if the command is not forwarded to execution | Request for enabling digital output |
| *GETIMG# | GETIMG param Possible parameter values: param = OK if the command is forwarded to execution param = ER if the command is not forwarded to execution | Request for taking picture (if the camera is connected) |
| *CLRDOUT param# Param=0 Param=1 Param=0,1 | CRLDOUT param Possible parameter values: param = OK if the command is forwarded to execution param = ER if the command is not forwarded to execution | Request for enabling digital output |
| *GETDOUT# | DOUT 0=1 1=0 где: output_number=output_state | Request for state of digital output |
| *CONNECT# | CONNECT CS_address:port | Request for establishing connection of Terminal with CS |
| *GETLINK# | LINK # LINK ip4_CS_address:port date_and_time | Request for status of connection to CS |
| *GETINFO# | INFO DID=deviceID HW=hardware_code_version BL=bootloader_version FW=firmware_version REC=number_of_records_in_archive IMEI=GSM_modem_unique_identifier | Request for state of terminal |
| *RESET# | RESET param Possible parameter values: param = OK if the command is forwarded to execution param = ER if the command is not forwarded to execution | Reset of terminal |
| *GETSTAT# | STAT terminal_date_and_time GPS=position as per GPS SPD=speed IGN=ignition_state L1=fuel_level:sensor_state L6=fuel_level:sensor_state Fuel level sensor state codes LLS/ • 0 - disabled; • 1 - not ready; • 2 - ready, , frequency 20 - max Hz; • 3 - error, frequency 0 - 19 Hz; | Request for vehicle state |
| *SETPWDID vid pwdid# vid - identification of Terminal; pwdid - password/identification. | SETPWDID ERRID/ERRNulPWD/ERRAlrSet/PWD:pwdid OK | Setting parameter “Password” |
| *CONNECTSC# | CONNECT SC | Request for connection of terminal with configurator server |
| *SETAPN apn# apn - APN of the operator | SETAPN apn ERR/OK | Setting APN |
| *SETAPN2 apn# apn - APN of the operator of second SIM card | SETAPN apn ERR/OK | Setting APN for second SIM card |
| *GPSCOLD# | GPSCOLD ERR/OK | Cold start of GPS reciever |
| *UNBLOCK# | Unblocking the terminal | |
| *SGPSINFO# | Smooth position type: N, VID=xxxxxxxxxx N = 0/1/2 0 – smoothing disabled 1 – smoothing enabled, filter 1 in use 2 – smoothing enabled, filter 2 in use VID – terminal ID | Request information about the current status of the coordinate filtering algorithm |
| *SGPS0# | OFF smooth position, VID=xxxxxxxxxx | Disable smoothing algorithm |
| *SGPS1# | ON smooth position method 1, VID=xxxxxxxxxx | Enable smoothing (filter 1) |
| *SGPS2# | ON smooth position method 2, VID=xxxxxxxxxx | Enable smoothing (filter 2) |
| *GETCNTINFO# | GETCNTINFO LLS1: CNTmin1, CNTmax1, CNT_T LLS2: ….VID = 336xxxxxxx | Request current CNT readings |
| *SETCNT pwd numlls CNTmin2 СNTmax2# | SETCNT OK – SMS worked correctly SETCNT PWD ERR – wrong or no password entered (see Limitations) SETCNT ERRVALUE – the entered CNT values do not comply with the Limits SETCNT ERRPARAM – incorrect SMS format | Set new СNT_empty/full values (CNTmin2 and СNTmax2) |
| *SETCNTFULL pwd numlls koef_empty# | SETCNTFULL OK – SMS worked correctly SETCNT PWD ERR – wrong or no password entered (see Limitations) SETCNTFULL ERRVALUE – Conditions outlined in the Limitations were not met SETCNT ERRPARAM – wrong SMS format | Automatic correction of the CNT_empty/full values |
| *SETCANSPD X# X – data rate of CAN 0 - 250 kb/s 1 - 125 kb/s 2 - 250 kb/s 3 - 500 kb/s 4 - 1 Mb/s 5 - 50 kb/s 6 - 62,5 kb/s | SETCANSPD OK – SMS worked correctly | Set data rate of CAN-interface (starting from FW-311) Default value - 250 kb/s |
| *GETCANSPD# | can speed = Х X – data rate value CAN 0 - 250 kb/s 1 - 125 kb/s 2 - 250 kb/s 3 - 500 kb/s 4 - 1 Mb/s 5 - 50 kb/s 6 - 62,5 kb/s CAN SPEED = ER - incorrect value of data rate (default value - 250 kb/s) | CAN interface data rate request (starting from FW-311) |
For the command Automatic correction of the CNT_empty/full values:
Recalculation formula:
CNTmin2 = CNTmin1 + koef_empty*(|CNTmax1-CNT_T|)
CNTmax2 = CNT_T
If koef_empty = 0, then CNT_empty does not change (CNTmin2=CNTmin1)
If koef_empty = 1, then CNT_empty increases by the same ∆ as CNT_full
CNT_full (CNTmax2) is assigned the value of the current CNT_T level
