The “Track” report allows a user to view of one selected VH for the selected time.

1. Select a VH
2. Select a period of time for report generation
3. Press “Add report” button and select “Track”

A map with the VH's track for this period of time will be displayed in the program window:

To display a tooltip press the VH icon .

The tooltip contains the following information:

• “Date” is the date and time the VH presence in the selected part of the track
• “Registration number” is the VH name
• “Speed” is a speed of the VH in the selected place of the track
• “Address” is the address where the VH was found in the selected place of the track
• “Mileage” is a VH mileage starting from the track beginning
• “LLS 5 correction, l” – the difference in the volume of fuel filled based on the correction results
• “Fuel volume in the primary tank” is a volume of fuel in the primary tank. It is not displayed, if the fuel level sensors are not connected or “0” number of sensors is set in the VH profile settings. The units of fuel parameters measurement (liters or gallons) shall be given according to the server settings
• “Fuel volume in the additional tank” is a volume of fuel in the additional tank (if there is such). It is not displayed, if the fuel level sensors are not connected or “0” number of sensors is set in the VH profile settings. The units of fuel parameters measurement (liters or gallons) shall be given according to the server settings
• “Ignition” is a position of the ignition key (on/off) in the selected place of the track
• “GPS data” are correct or incorrect data. If the data are incorrect, the date and time of receipt of the certain data are displayed
• “Total mileage as per CAN” – total vehicle mileage according to CAN bus data
• “Current auxiliary equipment readings” - current value or status of the auxiliary equipment
• “Driver” – driver registered on the vehicle

The format of the address and the content of the pop-up information about the vehicle can be configured in the object tree (see. Settings of objects tree).

To set up the report, press the right mouse button and select “Report settings”:

Configure the route displaying:

• Disabled - during the track vehicle parameters and auxiliary equipment operation are not considered
• During the movement
  • Select the color of a track segment which was completed with exceeding the speed allowed
  • Select the color of a track segment which was completed with ignition off

• In the operation of auxiliary equipment
  • Select the color of a track segment which was completed with auxiliary equipment turned on
  • Enter an appropriate name for auxiliary equipment, which will be displayed in vehicles profile under “Name of the equipment at the universal input” ( see Omnicomm Online. Administration Manual. The "Profile editing" section / "Universal input settings")

For an automatic track update right-click and select “Enable track autoupdate”. This setting is applicable for one vehicle only and Automatic updates every 30 seconds.

Measuring parameters between two points of the track

1. Right-click on the track and select “Track Section Parameters”
2. Select the starting point for the measurement on the track
3. Select the end point for the measurement on the track. To clear the selection, click anywhere on the map (not on the track).

For a section of the track, the following information is displayed:

• Vehicle name
• Period
• Mileage
• Fuel consumption
• Average speed
• Track section start address
• Track section end address

Exit the parameter measurement mode by pressing Enter or Esc.

To display track points, right-click and select “Track Detailing”.

The map in OpenStreetMaps mode has a feature enabling additional painting of necessary section of maps, please see www.openstreetmap.org for details.

If it is required to zoom in the map section, select it with the mouse cursor continuously pressing “Shift” button.

To create a geofence using a track it is required to use the map control panel.

A “Location” report allows to monitor movement of the VH in the real time mode. Information on the VH is refreshed upon receipt of the new data.

The location is recorded according to the valid GPS data (upon identification over 3 satellites).

For more effective tracking of moving objects in the real time mode we suggest that you use “VH tracking” mode. For more effective tracking of objects in geofences please use “Hide VH outside geofences” mode.

“Location” report in a normal mode

1. Select one or several VH
2. Open “Mapping” tab and select “Location”

In the program window the map with the VH location will be displayed:

To view information on the VH move the cursor to the VH icon. To pin the tooltip window with the information on VH, press the left mouse button.

This report contains the following information on the VH:

• VH name is a name or registration number of the VH
• Date is a date of the last received data in DD/MM/YYYY HH:MM:SS format
• Speed, (km/h) is a speed of the VH at the moment of data transfer
• Address is an address of the last location
• Volume of fuel in primary tank is a volume of fuel in the primary tank at the moment of data transfer
• Volume of fuel in the additional tank is a volume of fuel in the additional tank (if there is such) at the moment of data transfer
• Ignition is on/off
• The date and time of the last correct GPS data are displayed if within 60 seconds, there were not valid data.
• Total mileage as per CAN – total vehicle mileage according to CAN bus data
• Current auxiliary equipment readings - current value or status of the auxiliary equipment
• Driver – driver registered on the vehicle

The format of the address and the content of the pop-up information about the vehicle can be configured in the object tree (see Settings of objects tree).

“Location” report in vehicle tracking mode

“VH tracking” enables automatic actualization of map display, providing permanent display of the VH in center of the map section.

In case for generation of “Location” report several VH are selected, it is required to select one VH pressing the left mouse button on the icon of the required VH. The name of the selected VH will be highlighted in red. In the vehicle menu, select to “Enable the tracking mode of the selected vehicle”.

Switching on the mode of the VH tracking enables recording of the report and when selecting another object or period the recorded report will not change. The report recording allows you to view reports on other objects simultaneously. After switching off of the VH tracking mode, the report is not automatically recorded.

“Location” report in the mode of the VH hiding outside the geofences

“Mode of VH hiding outside geofences” allows changing of the VH icons located outside the geofences:

The full name of the geofence is displayed when you hover the mouse over it.